What do we cut to size?
- Beams and posts to length: Douglas fir, spruce, pressure-treated pine, Okan and oak. See timber sizes.
- Boards and battens to length, for example for a fence, cladding or a frame.
- Sheet material in strips or panels: plywood 9, 12 and 18 mm, film-faced plywood 12 and 18 mm, OSB, underlayment and chipboard.
Special cuts such as mitres, angled ends or notches are assessed in the shop. Ask on the spot so you know where you stand.
Sheet material in stock
| Sheet | Thickness and size | Price from |
|---|---|---|
| Plywood | 9 mm, 1.22 × 2.44 m | €38.05 |
| Plywood | 12 mm, 1.22 × 2.44 m | €48.70 |
| Plywood | 18 mm, 1.22 × 2.44 m | €69.70 |
| Film-faced plywood | 12 mm, 1.25 × 2.50 m | €56.05 |
| Film-faced plywood | 18 mm, 1.25 × 2.50 m | €74.75 |
| OSB | 9 mm, 1.22 × 2.44 m | €20.50 |
| OSB | 18 mm, 0.61 × 2.44 m | €18.80 |
| Underlayment | 9 mm, 1.22 × 2.44 m | €22.00 |
| Underlayment | 18 mm, 1.22 × 2.44 m | €39.95 |
| Chipboard | 18 mm, 0.61 × 2.44 m | €18.70 |
Prices per full sheet, prices as of 2 November 2026, incl. VAT. The first 5 cuts are free; more cuts are charged.
How to prepare for the shop
- List the timber, the cross-section and the net length for each part.
- Add the quantity and mark parts that must fit exactly.
- For sheet material, note which face stays visible.
- Bring the list or a photo of your sketch to the shop in Meppel.
| Part | Material | Length | Qty |
|---|---|---|---|
| Post | Douglas fir 120 × 120 mm | 2.60 m | 4 |
| Purlin | Douglas fir 70 × 200 mm | 3.40 m | 2 |
| Batten | Douglas fir 45 × 70 mm | 3.20 m | 8 |
The example above is an open pergola of about 3 × 3 metres. For a covered version, read canopy against the house.
Why have it cut to size?
- Less sawing and waste at home or on site.
- Cut parts fit more easily in your car or trailer.
After cutting, treat the end grain: open cuts absorb water fastest. Seal the cut edges of sheet material with primer or paint.
Where and when?
Cutting is done in the shop in Meppel during opening hours. Directions and opening hours: contact.
Frequently asked questions
Can I have timber cut to size at Jan Sok?
Yes, in our shop in Meppel. You buy beams, boards, battens, posts or sheet material and have them cut to size there.
What does cutting to size cost?
The first 5 cuts are free. More cuts are charged; ask in the shop for the rate.
Do you cut to size for online orders or delivery?
No. Cutting to size is only possible in the shop in Meppel.
Do you also cut sheet material to size?
Yes, plywood, film-faced plywood, OSB, underlayment and chipboard too. Bring net sizes and say which face should be the good side.
Do I need to allow for saw loss?
Every cut takes a few millimetres. If you calculate yourself, add 5 to 10 percent extra material. For decking this is usually not needed.
