Click the image to see the section size and grain
| Brand | Houthandel Jan Sok |
|---|---|
| Finish | Grijs |
| Material | polyvinylchloride |
| Volume | 1 piece |
| Stock | 100 in stock |
Product description
With this PVC drain end cap Ø80 you close off the open end of a drainage pipe with a diameter of 80 mm. You use it at the start of a drain run, so at the highest point of the pipe, where the water does not yet need to go anywhere. Without an end cap, sand, soil or gravel can wash into the pipe there, so the drain slowly silts up and carries away less water. You slide the cap over the end of the corrugated drainage pipe. Lay the capped start of the run slightly higher than the outfall point, so the water flows with a fall towards the ditch, sump or sewer. A common tip: mark the start of the run with a small stake or note the location, so you know later where to dig if you want to flush or extend the drainage. You simply order the end cap online from Houthandel Jan Sok and collect it at Celsius 10 in Meppel, or have it delivered to your home.
Key features
- Diameter Ø80: fits 80 mm drainage pipe.
- Prevents silting up: keeps sand, soil and gravel out of the open end of the pipe.
- For the start of the run: closes off the highest, dead-end point of your drainage pipe.
- PVC: rot-proof plastic that is suitable for lying in the ground.
- Quick to fit: slide over the pipe end, no glue or tools needed.
Applications
Suitable for, among other things:
- Garden drainage for a waterlogged lawn or border.
- Drainage around the foundations of a shed or summerhouse.
- Drainage along a patio or driveway.
- Closing off a branch that is not (yet) being extended.
Combine with
This cap belongs to a Ø80 drainage system:
- Drainage pipe Ø80 (corrugated, with or without wrap).
- PVC drain click coupler Ø80 to join pipe lengths.
- PVC drain tee Ø80 for branches.
- PVC drain reducer Ø110 x Ø80 to connect the run to the PVC drain pipe.
Installation
- Cut the pipe to length: saw the drainage pipe square between two corrugations and remove any burrs.
- Free up the wrap: push any coir or filter wrap back a little so the cap fits over the pipe.
- Fit the cap: slide the end cap fully over the pipe end.
- Replace the wrap: pull the wrap back over the end of the pipe up to the cap.
- Cover: lay the pipe to a fall and backfill with drainage sand or gravel before you put the soil back.
Product specifications
| Property | Value |
|---|---|
| Type | end cap for drainage pipe |
| Diameter | Ø80 mm |
| Material | PVC |
| Volume | 1 piece |
For beginners
Beginner
You fit an end cap on the start of a drainage pipe so no soil can run into the pipe. Make sure the cap is the same size as your pipe, in this case 80 mm.
- Tools
- Fine-toothed saw or secateurs for drainage pipe
- Tape measure
- Spade
- Also needed
- pvc-drain-klikmof-80
- pvc-drain-t-stuk-80
- pvc-drain-verloop-110-x-80
- How to calculate
- You buy this per piece; you need one for each dead end of your drainage.
- Common mistake
- Many people leave the start of the drainage pipe open in the ground. Sand then washes in and the pipe silts up, so always close off every dead end with a cap.
PVC drain end cap Ø80
Delivery and pickup
-
Pickup in Meppel: Free (ready after confirmation)
-
Truck delivery with a Moffett: €125 fixed delivery charge
-
Free delivery on orders from €2,500
Cut-to-size or custom-processed timber is non-returnable. Stock lengths: see returns policy.
Frequently asked questions
What do I use a drain end cap Ø80 for?
You use it to close off the open start of a Ø80 drainage pipe. This stops sand or soil running into the pipe, so the drainage keeps working well for longer.
Does the start of a drainage pipe need to be closed?
Yes, you close off the highest point of a drain run with a cap. The water enters through the perforations in the pipe, not through the open end.
Do I need to glue a drain end cap?
No, you slide a drain end cap over the corrugated pipe. Drainage works without pressure, so a glued joint is not needed.